MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #1 Center Console Radio Surround (LHD) MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #1 Center Console Radio Surround (LHD)
MR2Heaven MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #1 Center Console Radio Surround (LHD)
$724.99

  Purpose   We went all out on these trims to leave a lasting legacy, something we can be proud of and as a proof of concept for our other future endeavors. With that being said, long story short, we utilized cutting edge state of the art manufacturing methods and equipment and with no shortcuts taken. To make these very complexly shaped and detailed trims in full CF a reality, pre-preg/dry method is a must. These aren't your typical CF trims produced from inverted hand made fiberglass molds and vacuum bags in the garage, "sticker" type overlay trims with 3M tape, or skinned Carbon fiber layer simply laid over the original plastic trims. These are real high performance full pre-preg "dry" carbon fiber replacement trims meticulously hand crafted from an aluminum mold and completely cured under high pressure and heat in a massive autoclave throughout different stages over many hours. No original parts/plastic cores are needed or sacrificed as our whole trim is essentially a full replacement consisting of all carbon fiber, with an exception of a few critical mounting tabs made with durable nylon material and epoxied on   Click for more information How its made and advantages The original trims were 3D scanned up to 0.03-0.05mm accuracy and CADed for the best fit and accuracy possible. Next aluminum molds of each panel were made via CNC milling. Why make the mold from billet aluminum instead of fiberglass? To sum it up, carbon fiber parts are made either via "dry" or "wet" carbon. Basically the difference is in the production methods and the corresponding equipment needed/used. Aluminum molds offer significant and exclusive benefits such as the possible use of pre-pregnated carbon fiber (referred to as dry carbon production method) with optimal amounts of resin pre-infused in each layer and the required use of an autoclave for pressurized high heat curing over many stages throughout many hours. This extensive and expensive production process ensures complete curing of the part with the best quality possible to the highest of standards which cannot be matched with the lather wet carbon fiber part production method. Dry carbon method also allows for increased geometric complexity (these interior trims are quite complex in shapes, angles and not possible to make via the traditional cheaper "wet" method). Dry carbon offers desirable and unrivaled qualities such as being vastly lighter (typically 60% lighter vs wet carbon counterpart) yet significantly stronger while being much much thinner, increased uniformity, increased strength with less air pockets, unbeatable smooth surface finish with higher accuracy and precision. Dry carbon is the same tech used by F1 and hard core race teams (where teams commonly invest dozens of millions of USD worth of the best tech, design and parts into a compact race car, essentially the best of the best available), military as well as in the aerospace/satellite industries across the world. The lather choice would be wet carbon with fiberglass molds which is the common method of production for the huge majority of the carbon fiber parts on the market. Wet carbon is mostly for appearance and not for function. Results The photos and results speak for themselves. Complete replacement trims in carbon fiber molded elegantly into very complex shapes that many people thought simply weren't possible. These trims breathe beauty, classy, high end, exoticness, sportiness, faithfulness to the original design, cutting edge technology, high accuracy, high performance and simply jaw dropping amusement. These trims are as high end, lightweight and exotic as it gets. Its the first of its kind in over 30 years for the MR2 community and to note that even for many other popular car platforms including modern BMWs, Audis, Porsches, Mercedes Benz, from OE and aftermarket companies alike do not have any interior trim comparatives of this caliber, unless it is on their dedicated race cars. For comparatives, look closer to Ferrari, F1, hardcore multi 6 figure race cars, Paganis and multi million dollar hypercars. Have your friends hold the extremely lightweight pieces and watch their expression turn to awe, resemble as if they just witnessed a miracle. -As if the lightweight and strength aspect of the pieces alone when considering the actual size and dimensions of the part almost defies physics and is out of this world. Due to the high cost to stock up in bulk quantities, complexity, intensive labor, and significant time needed to produce each of these trims with the extremely limited molds we developed, only 1 of each variant is able to be produced every 1-2 days, or around 10-15 pcs a month. We will be keeping very limited stock on hand and these will be mostly made in batches as orders come in Features Made with full Pre-Preg/Dry Carbon Fiber Crafted out of special Aluminum molds/Autoclave cured under high heat and pressure in numerous different stages over many hours for the highest performance and quality possible Durable Nylon plastic mounting clips are epoxied on. Some small intrinsic details are molded/integrated with the numerous carbon layers for high durability and some areas are CNCed milled. Extremely lightweight. Some smaller trims like the door cup cover are similar to a piece of paper in weight at around 0.6oz. Our window switch cover is around 1.8oz. All functions and components install on and work as OEM intended. Full plug and play   Fitment   1991-1998 Toyota MR2. Please pay attention if your car is LHD (Left hand drive) or RHD (Right hand drive). Some trims will only work for one and not the other!   Notes These trims are all meticulously hand crafted and as such, no single trim is identical to another and each trim is unique.  Only the carbon trims are included. Actual window switches pictured are not included This page is for #1 Center Console LHD Trim only

MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #2 Gauge Cluster - Left Vent (LHD) MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #2 Gauge Cluster - Left Vent (LHD)
MR2Heaven MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #2 Gauge Cluster - Left Vent (LHD)
$524.99

Purpose   We went all out on these trims to leave a lasting legacy, something we can be proud of and as a proof of concept for our other future endeavors. With that being said, long story short, we utilized cutting edge state of the art manufacturing methods and equipment and with no shortcuts taken. To make these very complexly shaped and detailed trims in full CF a reality, pre-preg/dry method is a must. These aren't your typical CF trims produced from inverted hand made fiberglass molds and vacuum bags in the garage, "sticker" type overlay trims with 3M tape, or skinned Carbon fiber layer simply laid over the original plastic trims. These are real high performance full pre-preg "dry" carbon fiber replacement trims meticulously hand crafted from an aluminum mold and completely cured under high pressure and heat in a massive autoclave throughout different stages over many hours. No original parts/plastic cores are needed or sacrificed as our whole trim is essentially a full replacement consisting of all carbon fiber, with an exception of a few critical mounting tabs made with durable nylon material and epoxied on   Click for more information How its made and advantages The original trims were 3D scanned up to 0.03-0.05mm accuracy and CADed for the best fit and accuracy possible. Next aluminum molds of each panel were made via CNC milling. Why make the mold from billet aluminum instead of fiberglass? To sum it up, carbon fiber parts are made either via "dry" or "wet" carbon. Basically the difference is in the production methods and the corresponding equipment needed/used. Aluminum molds offer significant and exclusive benefits such as the possible use of pre-pregnated carbon fiber (referred to as dry carbon production method) with optimal amounts of resin pre-infused in each layer and the required use of an autoclave for pressurized high heat curing over many stages throughout many hours. This extensive and expensive production process ensures complete curing of the part with the best quality possible to the highest of standards which cannot be matched with the lather wet carbon fiber part production method. Dry carbon method also allows for increased geometric complexity (these interior trims are quite complex in shapes, angles and not possible to make via the traditional cheaper "wet" method). Dry carbon offers desirable and unrivaled qualities such as being vastly lighter (typically 60% lighter vs wet carbon counterpart) yet significantly stronger while being much much thinner, increased uniformity, increased strength with less air pockets, unbeatable smooth surface finish with higher accuracy and precision. Dry carbon is the same tech used by F1 and hard core race teams (where teams commonly invest dozens of millions of USD worth of the best tech, design and parts into a compact race car, essentially the best of the best available), military as well as in the aerospace/satellite industries across the world. The lather choice would be wet carbon with fiberglass molds which is the common method of production for the huge majority of the carbon fiber parts on the market. Wet carbon is mostly for appearance and not for function. Results The photos and results speak for themselves. Complete replacement trims in carbon fiber molded elegantly into very complex shapes that many people thought simply weren't possible. These trims breathe beauty, classy, high end, exoticness, sportiness, faithfulness to the original design, cutting edge technology, high accuracy, high performance and simply jaw dropping amusement. These trims are as high end, lightweight and exotic as it gets. Its the first of its kind in over 30 years for the MR2 community and to note that even for many other popular car platforms including modern BMWs, Audis, Porsches, Mercedes Benz, from OE and aftermarket companies alike do not have any interior trim comparatives of this caliber, unless it is on their dedicated race cars. For comparatives, look closer to Ferrari, F1, hardcore multi 6 figure race cars, Paganis and multi million dollar hypercars. Have your friends hold the extremely lightweight pieces and watch their expression turn to awe, resemble as if they just witnessed a miracle. -As if the lightweight and strength aspect of the pieces alone when considering the actual size and dimensions of the part almost defies physics and is out of this world. Due to the high cost to stock up in bulk quantities, complexity, intensive labor, and significant time needed to produce each of these trims with the extremely limited molds we developed, only 1 of each variant is able to be produced every 1-2 days, or around 10-15 pcs a month. We will be keeping very limited stock on hand and these will be mostly made in batches as orders come in Features Made with full Pre-Preg/Dry Carbon Fiber Crafted out of special Aluminum molds/Autoclave cured under high heat and pressure in numerous different stages over many hours for the highest performance and quality possible Durable Nylon plastic mounting clips are epoxied on. Some small intrinsic details are molded/integrated with the numerous carbon layers for high durability and some areas are CNCed milled. Extremely lightweight. Some smaller trims like the door cup cover are similar to a piece of paper in weight at around 0.6oz. Our window switch cover is around 1.8oz. All functions and components install on and work as OEM intended. Full plug and play   Fitment   1991-1998 Toyota MR2. Please pay attention if your car is LHD (Left hand drive) or RHD (Right hand drive). Some trims will only work for one and not the other!   Notes These trims are all meticulously hand crafted and as such, no single trim is identical to another and each trim is unique.  Only the carbon trims are included. Actual window switches pictured are not included This page is for #2 Gauge Cluster - Left Vent (LHD) Only

MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #3 Right Side Air Vent (LHD) MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #3 Right Side Air Vent (LHD)
MR2Heaven MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #3 Right Side Air Vent (LHD)
$289.99

  Purpose   We went all out on these trims to leave a lasting legacy, something we can be proud of and as a proof of concept for our other future endeavors. With that being said, long story short, we utilized cutting edge state of the art manufacturing methods and equipment and with no shortcuts taken. To make these very complexly shaped and detailed trims in full CF a reality, pre-preg/dry method is a must. These aren't your typical CF trims produced from inverted hand made fiberglass molds and vacuum bags in the garage, "sticker" type overlay trims with 3M tape, or skinned Carbon fiber layer simply laid over the original plastic trims. These are real high performance full pre-preg "dry" carbon fiber replacement trims meticulously hand crafted from an aluminum mold and completely cured under high pressure and heat in a massive autoclave throughout different stages over many hours. No original parts/plastic cores are needed or sacrificed as our whole trim is essentially a full replacement consisting of all carbon fiber, with an exception of a few critical mounting tabs made with durable nylon material and epoxied on   Click for more information How its made and advantages The original trims were 3D scanned up to 0.03-0.05mm accuracy and CADed for the best fit and accuracy possible. Next aluminum molds of each panel were made via CNC milling. Why make the mold from billet aluminum instead of fiberglass? To sum it up, carbon fiber parts are made either via "dry" or "wet" carbon. Basically the difference is in the production methods and the corresponding equipment needed/used. Aluminum molds offer significant and exclusive benefits such as the possible use of pre-pregnated carbon fiber (referred to as dry carbon production method) with optimal amounts of resin pre-infused in each layer and the required use of an autoclave for pressurized high heat curing over many stages throughout many hours. This extensive and expensive production process ensures complete curing of the part with the best quality possible to the highest of standards which cannot be matched with the lather wet carbon fiber part production method. Dry carbon method also allows for increased geometric complexity (these interior trims are quite complex in shapes, angles and not possible to make via the traditional cheaper "wet" method). Dry carbon offers desirable and unrivaled qualities such as being vastly lighter (typically 60% lighter vs wet carbon counterpart) yet significantly stronger while being much much thinner, increased uniformity, increased strength with less air pockets, unbeatable smooth surface finish with higher accuracy and precision. Dry carbon is the same tech used by F1 and hard core race teams (where teams commonly invest dozens of millions of USD worth of the best tech, design and parts into a compact race car, essentially the best of the best available), military as well as in the aerospace/satellite industries across the world. The lather choice would be wet carbon with fiberglass molds which is the common method of production for the huge majority of the carbon fiber parts on the market. Wet carbon is mostly for appearance and not for function. Results The photos and results speak for themselves. Complete replacement trims in carbon fiber molded elegantly into very complex shapes that many people thought simply weren't possible. These trims breathe beauty, classy, high end, exoticness, sportiness, faithfulness to the original design, cutting edge technology, high accuracy, high performance and simply jaw dropping amusement. These trims are as high end, lightweight and exotic as it gets. Its the first of its kind in over 30 years for the MR2 community and to note that even for many other popular car platforms including modern BMWs, Audis, Porsches, Mercedes Benz, from OE and aftermarket companies alike do not have any interior trim comparatives of this caliber, unless it is on their dedicated race cars. For comparatives, look closer to Ferrari, F1, hardcore multi 6 figure race cars, Paganis and multi million dollar hypercars. Have your friends hold the extremely lightweight pieces and watch their expression turn to awe, resemble as if they just witnessed a miracle. -As if the lightweight and strength aspect of the pieces alone when considering the actual size and dimensions of the part almost defies physics and is out of this world. Due to the high cost to stock up in bulk quantities, complexity, intensive labor, and significant time needed to produce each of these trims with the extremely limited molds we developed, only 1 of each variant is able to be produced every 1-2 days, or around 10-15 pcs a month. We will be keeping very limited stock on hand and these will be mostly made in batches as orders come in Features Made with full Pre-Preg/Dry Carbon Fiber Crafted out of special Aluminum molds/Autoclave cured under high heat and pressure in numerous different stages over many hours for the highest performance and quality possible Durable Nylon plastic mounting clips are epoxied on. Some small intrinsic details are molded/integrated with the numerous carbon layers for high durability and some areas are CNCed milled. Extremely lightweight. Some smaller trims like the door cup cover are similar to a piece of paper in weight at around 0.6oz. Our window switch cover is around 1.8oz. All functions and components install on and work as OEM intended. Full plug and play   Fitment   1991-1998 Toyota MR2. Please pay attention if your car is LHD (Left hand drive) or RHD (Right hand drive). Some trims will only work for one and not the other!   Notes These trims are all meticulously hand crafted and as such, no single trim is identical to another and each trim is unique.  Only the carbon trims are included. Actual window switches pictured are not included This page is for #3Right Side Air Vent (LHD) Only!

MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #4 OEM Shifter Trim Cover (LHD & RHD) MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #4 OEM Shifter Trim Cover (LHD & RHD)
MR2Heaven MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #4 OEM Shifter Trim Cover (LHD & RHD)
$275.99

  Purpose   We went all out on these trims to leave a lasting legacy, something we can be proud of and as a proof of concept for our other future endeavors. With that being said, long story short, we utilized cutting edge state of the art manufacturing methods and equipment and with no shortcuts taken. To make these very complexly shaped and detailed trims in full CF a reality, pre-preg/dry method is a must. These aren't your typical CF trims produced from inverted hand made fiberglass molds and vacuum bags in the garage, "sticker" type overlay trims with 3M tape, or skinned Carbon fiber layer simply laid over the original plastic trims. These are real high performance full pre-preg "dry" carbon fiber replacement trims meticulously hand crafted from an aluminum mold and completely cured under high pressure and heat in a massive autoclave throughout different stages over many hours. No original parts/plastic cores are needed or sacrificed as our whole trim is essentially a full replacement consisting of all carbon fiber, with an exception of a few critical mounting tabs made with durable nylon material and epoxied on   Click for more information How its made and advantages The original trims were 3D scanned up to 0.03-0.05mm accuracy and CADed for the best fit and accuracy possible. Next aluminum molds of each panel were made via CNC milling. Why make the mold from billet aluminum instead of fiberglass? To sum it up, carbon fiber parts are made either via "dry" or "wet" carbon. Basically the difference is in the production methods and the corresponding equipment needed/used. Aluminum molds offer significant and exclusive benefits such as the possible use of pre-pregnated carbon fiber (referred to as dry carbon production method) with optimal amounts of resin pre-infused in each layer and the required use of an autoclave for pressurized high heat curing over many stages throughout many hours. This extensive and expensive production process ensures complete curing of the part with the best quality possible to the highest of standards which cannot be matched with the lather wet carbon fiber part production method. Dry carbon method also allows for increased geometric complexity (these interior trims are quite complex in shapes, angles and not possible to make via the traditional cheaper "wet" method). Dry carbon offers desirable and unrivaled qualities such as being vastly lighter (typically 60% lighter vs wet carbon counterpart) yet significantly stronger while being much much thinner, increased uniformity, increased strength with less air pockets, unbeatable smooth surface finish with higher accuracy and precision. Dry carbon is the same tech used by F1 and hard core race teams (where teams commonly invest dozens of millions of USD worth of the best tech, design and parts into a compact race car, essentially the best of the best available), military as well as in the aerospace/satellite industries across the world. The lather choice would be wet carbon with fiberglass molds which is the common method of production for the huge majority of the carbon fiber parts on the market. Wet carbon is mostly for appearance and not for function. Results The photos and results speak for themselves. Complete replacement trims in carbon fiber molded elegantly into very complex shapes that many people thought simply weren't possible. These trims breathe beauty, classy, high end, exoticness, sportiness, faithfulness to the original design, cutting edge technology, high accuracy, high performance and simply jaw dropping amusement. These trims are as high end, lightweight and exotic as it gets. Its the first of its kind in over 30 years for the MR2 community and to note that even for many other popular car platforms including modern BMWs, Audis, Porsches, Mercedes Benz, from OE and aftermarket companies alike do not have any interior trim comparatives of this caliber, unless it is on their dedicated race cars. For comparatives, look closer to Ferrari, F1, hardcore multi 6 figure race cars, Paganis and multi million dollar hypercars. Have your friends hold the extremely lightweight pieces and watch their expression turn to awe, resemble as if they just witnessed a miracle. -As if the lightweight and strength aspect of the pieces alone when considering the actual size and dimensions of the part almost defies physics and is out of this world. Due to the high cost to stock up in bulk quantities, complexity, intensive labor, and significant time needed to produce each of these trims with the extremely limited molds we developed, only 1 of each variant is able to be produced every 1-2 days, or around 10-15 pcs a month. We will be keeping very limited stock on hand and these will be mostly made in batches as orders come in Features Made with full Pre-Preg/Dry Carbon Fiber Crafted out of special Aluminum molds/Autoclave cured under high heat and pressure in numerous different stages over many hours for the highest performance and quality possible Durable Nylon plastic mounting clips are epoxied on. Some small intrinsic details are molded/integrated with the numerous carbon layers for high durability and some areas are CNCed milled. Extremely lightweight. Some smaller trims like the door cup cover are similar to a piece of paper in weight at around 0.6oz. Our window switch cover is around 1.8oz. All functions and components install on and work as OEM intended. Full plug and play   Fitment   1991-1998 Toyota MR2. Please pay attention if your car is LHD (Left hand drive) or RHD (Right hand drive). Some trims will only work for one and not the other!   Notes These trims are all meticulously hand crafted and as such, no single trim is identical to another and each trim is unique.  Only the carbon trims are included. Actual window switches pictured are not included This page is for #4 OEM Style Shifter Trim Cover (LHD & RHD) Only!

MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #5 and #6 - Door Cup Handle Covers (LHD and RHD) MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #5 and #6 - Door Cup Handle Covers (LHD and RHD)
MR2Heaven MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #5 and #6 - Door Cup Handle Covers (LHD and RHD)
$419.99

  Purpose   We went all out on these trims to leave a lasting legacy, something we can be proud of and as a proof of concept for our other future endeavors. With that being said, long story short, we utilized cutting edge state of the art manufacturing methods and equipment and with no shortcuts taken. To make these very complexly shaped and detailed trims in full CF a reality, pre-preg/dry method is a must. These aren't your typical CF trims produced from inverted hand made fiberglass molds and vacuum bags in the garage, "sticker" type overlay trims with 3M tape, or skinned Carbon fiber layer simply laid over the original plastic trims. These are real high performance full pre-preg "dry" carbon fiber replacement trims meticulously hand crafted from an aluminum mold and completely cured under high pressure and heat in a massive autoclave throughout different stages over many hours. No original parts/plastic cores are needed or sacrificed as our whole trim is essentially a full replacement consisting of all carbon fiber, with an exception of a few critical mounting tabs made with durable nylon material and epoxied on   Click for more information How its made and advantages The original trims were 3D scanned up to 0.03-0.05mm accuracy and CADed for the best fit and accuracy possible. Next aluminum molds of each panel were made via CNC milling. Why make the mold from billet aluminum instead of fiberglass? To sum it up, carbon fiber parts are made either via "dry" or "wet" carbon. Basically the difference is in the production methods and the corresponding equipment needed/used. Aluminum molds offer significant and exclusive benefits such as the possible use of pre-pregnated carbon fiber (referred to as dry carbon production method) with optimal amounts of resin pre-infused in each layer and the required use of an autoclave for pressurized high heat curing over many stages throughout many hours. This extensive and expensive production process ensures complete curing of the part with the best quality possible to the highest of standards which cannot be matched with the lather wet carbon fiber part production method. Dry carbon method also allows for increased geometric complexity (these interior trims are quite complex in shapes, angles and not possible to make via the traditional cheaper "wet" method). Dry carbon offers desirable and unrivaled qualities such as being vastly lighter (typically 60% lighter vs wet carbon counterpart) yet significantly stronger while being much much thinner, increased uniformity, increased strength with less air pockets, unbeatable smooth surface finish with higher accuracy and precision. Dry carbon is the same tech used by F1 and hard core race teams (where teams commonly invest dozens of millions of USD worth of the best tech, design and parts into a compact race car, essentially the best of the best available), military as well as in the aerospace/satellite industries across the world. The lather choice would be wet carbon with fiberglass molds which is the common method of production for the huge majority of the carbon fiber parts on the market. Wet carbon is mostly for appearance and not for function. Results The photos and results speak for themselves. Complete replacement trims in carbon fiber molded elegantly into very complex shapes that many people thought simply weren't possible. These trims breathe beauty, classy, high end, exoticness, sportiness, faithfulness to the original design, cutting edge technology, high accuracy, high performance and simply jaw dropping amusement. These trims are as high end, lightweight and exotic as it gets. Its the first of its kind in over 30 years for the MR2 community and to note that even for many other popular car platforms including modern BMWs, Audis, Porsches, Mercedes Benz, from OE and aftermarket companies alike do not have any interior trim comparatives of this caliber, unless it is on their dedicated race cars. For comparatives, look closer to Ferrari, F1, hardcore multi 6 figure race cars, Paganis and multi million dollar hypercars. Have your friends hold the extremely lightweight pieces and watch their expression turn to awe, resemble as if they just witnessed a miracle. -As if the lightweight and strength aspect of the pieces alone when considering the actual size and dimensions of the part almost defies physics and is out of this world. Due to the high cost to stock up in bulk quantities, complexity, intensive labor, and significant time needed to produce each of these trims with the extremely limited molds we developed, only 1 of each variant is able to be produced every 1-2 days, or around 10-15 pcs a month. We will be keeping very limited stock on hand and these will be mostly made in batches as orders come in Features Made with full Pre-Preg/Dry Carbon Fiber Crafted out of special Aluminum molds/Autoclave cured under high heat and pressure in numerous different stages over many hours for the highest performance and quality possible Durable Nylon plastic mounting clips are epoxied on. Some small intrinsic details are molded/integrated with the numerous carbon layers for high durability and some areas are CNCed milled. Extremely lightweight. Some smaller trims like the door cup cover are similar to a piece of paper in weight at around 0.6oz. Our window switch cover is around 1.8oz. All functions and components install on and work as OEM intended. Full plug and play   Fitment   1991-1998 Toyota MR2. Please pay attention if your car is LHD (Left hand drive) or RHD (Right hand drive). Some trims will only work for one and not the other!   Notes These trims are all meticulously hand crafted and as such, no single trim is identical to another and each trim is unique.  Only the carbon trims are included. Actual window switches pictured are not included This page is for #5 and #6 Door Cup Handle Covers - Left and Right Side (LHD and RHD) Only!

MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #7 and #8 - Window Switch Trims (LHD) MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #7 and #8 - Window Switch Trims (LHD)
MR2Heaven MR2Heaven Full Pre-Preg/Dry Carbon Fiber Complete Replacement Interior Trim - #7 and #8 - Window Switch Trims (LHD)
$624.99

  Purpose   We went all out on these trims to leave a lasting legacy, something we can be proud of and as a proof of concept for our other future endeavors. With that being said, long story short, we utilized cutting edge state of the art manufacturing methods and equipment and with no shortcuts taken. To make these very complexly shaped and detailed trims in full CF a reality, pre-preg/dry method is a must. These aren't your typical CF trims produced from inverted hand made fiberglass molds and vacuum bags in the garage, "sticker" type overlay trims with 3M tape, or skinned Carbon fiber layer simply laid over the original plastic trims. These are real high performance full pre-preg "dry" carbon fiber replacement trims meticulously hand crafted from an aluminum mold and completely cured under high pressure and heat in a massive autoclave throughout different stages over many hours. No original parts/plastic cores are needed or sacrificed as our whole trim is essentially a full replacement consisting of all carbon fiber, with an exception of a few critical mounting tabs made with durable nylon material and epoxied on   Click for more information How its made and advantages The original trims were 3D scanned up to 0.03-0.05mm accuracy and CADed for the best fit and accuracy possible. Next aluminum molds of each panel were made via CNC milling. Why make the mold from billet aluminum instead of fiberglass? To sum it up, carbon fiber parts are made either via "dry" or "wet" carbon. Basically the difference is in the production methods and the corresponding equipment needed/used. Aluminum molds offer significant and exclusive benefits such as the possible use of pre-pregnated carbon fiber (referred to as dry carbon production method) with optimal amounts of resin pre-infused in each layer and the required use of an autoclave for pressurized high heat curing over many stages throughout many hours. This extensive and expensive production process ensures complete curing of the part with the best quality possible to the highest of standards which cannot be matched with the lather wet carbon fiber part production method. Dry carbon method also allows for increased geometric complexity (these interior trims are quite complex in shapes, angles and not possible to make via the traditional cheaper "wet" method). Dry carbon offers desirable and unrivaled qualities such as being vastly lighter (typically 60% lighter vs wet carbon counterpart) yet significantly stronger while being much much thinner, increased uniformity, increased strength with less air pockets, unbeatable smooth surface finish with higher accuracy and precision. Dry carbon is the same tech used by F1 and hard core race teams (where teams commonly invest dozens of millions of USD worth of the best tech, design and parts into a compact race car, essentially the best of the best available), military as well as in the aerospace/satellite industries across the world. The lather choice would be wet carbon with fiberglass molds which is the common method of production for the huge majority of the carbon fiber parts on the market. Wet carbon is mostly for appearance and not for function. Results The photos and results speak for themselves. Complete replacement trims in carbon fiber molded elegantly into very complex shapes that many people thought simply weren't possible. These trims breathe beauty, classy, high end, exoticness, sportiness, faithfulness to the original design, cutting edge technology, high accuracy, high performance and simply jaw dropping amusement. These trims are as high end, lightweight and exotic as it gets. Its the first of its kind in over 30 years for the MR2 community and to note that even for many other popular car platforms including modern BMWs, Audis, Porsches, Mercedes Benz, from OE and aftermarket companies alike do not have any interior trim comparatives of this caliber, unless it is on their dedicated race cars. For comparatives, look closer to Ferrari, F1, hardcore multi 6 figure race cars, Paganis and multi million dollar hypercars. Have your friends hold the extremely lightweight pieces and watch their expression turn to awe, resemble as if they just witnessed a miracle. -As if the lightweight and strength aspect of the pieces alone when considering the actual size and dimensions of the part almost defies physics and is out of this world. Due to the high cost to stock up in bulk quantities, complexity, intensive labor, and significant time needed to produce each of these trims with the extremely limited molds we developed, only 1 of each variant is able to be produced every 1-2 days, or around 10-15 pcs a month. We will be keeping very limited stock on hand and these will be mostly made in batches as orders come in Features Made with full Pre-Preg/Dry Carbon Fiber Crafted out of special Aluminum molds/Autoclave cured under high heat and pressure in numerous different stages over many hours for the highest performance and quality possible Durable Nylon plastic mounting clips are epoxied on. Some small intrinsic details are molded/integrated with the numerous carbon layers for high durability and some areas are CNCed milled. Extremely lightweight. Some smaller trims like the door cup cover are similar to a piece of paper in weight at around 0.6oz. Our window switch cover is around 1.8oz. All functions and components install on and work as OEM intended. Full plug and play   Fitment   1991-1998 Toyota MR2. Please pay attention if your car is LHD (Left hand drive) or RHD (Right hand drive). Some trims will only work for one and not the other!   Notes These trims are all meticulously hand crafted and as such, no single trim is identical to another and each trim is unique.  Only the carbon trims are included. Actual window switches pictured are not included This page is for #7 and #8 Window Switch Trims (Left and Right Side) (LHD) Only

MR2Heaven Forged Carbon Fiber License Plate Frame MR2Heaven Forged Carbon Fiber License Plate Frame
MR2Heaven MR2Heaven Forged Carbon Fiber License Plate Frame
$84.99

The MR2Heaven Forged Carbon Fiber license plate frame is manufactured with authentic forged carbon fiber, the same material used in $300,000 USD Lamborghinis, to create the lightest and coolest automotive parts out there Features Ultra light weight Sleek, modern and clean look Perfect for the performance aficionado Looks great on virtually any vehicle Easy to install 

OEM Style Wiper Blade Replacement Pair (For J Hook 1993+ and newer MR2s)
MR2Heaven OEM Style Wiper Blade Replacement Pair (For J Hook 1993+ and newer MR2s)
$19.99

Wiper blades are supposed to be replaced every six to 12 months to ensure proper performance, comfort and reliability Features Premium high quality natural rubber Good for all weather Teflon/PTFE coated blades for lower enhanced durability, lower coefficient of friction, prevents chattering and reduced noise 19" and 20" blades Direct plug and play - no modifications needed Fitment OEM Style Wiper Blade Replacement Pair (For 1993-1998 and newer MR2s) Notes Sold as a pair

MR2Heaven Brake Rotors - For 1991-1998 MR2 Big Brake Kit, 1994-1998 Twin Turbo Supra and 2004-2011 RX8 MR2Heaven Brake Rotors - For 1991-1998 MR2 Big Brake Kit, 1994-1998 Twin Turbo Supra and 2004-2011 RX8
MR2 Heaven MR2Heaven Brake Rotors - For 1991-1998 MR2 Big Brake Kit, 1994-1998 Twin Turbo Supra and 2004-2011 RX8
from $124.99

Note 6/11/2022 - Will be in stock in 3 months --- These rotors are used for our big brake kits but will also fit some Supras and RX8s Features 54 Curved Vane design for high air flow/cooling/thermal management G3000 Grade Iron material (OE Spec) Balanced and true Race/Track capable for MR2s High performance street capable/Light track duty for Supra and RX8s Fitment These rotors will fit Our 1991-1998 SW20 front and rear big brake kits 1994-1998 Toyota Supra Twin Turbo Front side rotors (Select our front rotors) 2004-2011 Mazda Rx8 Sport Suspension Trim Front side rotors (Select our rear rotors) Notes Sold as a set of 2 or 4 rotors

MR2Heaven Shifter Cup MR2Heaven Shifter Cup
MR2Heaven MR2Heaven Shifter Cup
$34.99

6/22/2022 - Ready to ship in about 1 week.  Features Drops shifter lever stick 3mm over OEM cup Revised angles for increased shifter actuation travel without interference up top with the cup 6 Recessed and filleted groves for lubrication  Tight fit by design to eliminate play Durable Nylon plastic construction Direct plug and play - No modifications needed Fitment Direct fit with our Hybrid 5 in 1 adjustable short shifter with 32.0 mm diameter spherical ball/base Note Shifter lever stick is not included

-47% sale
MR2Heaven 1991-1998 Reproduction Mud Guards/Mud Flaps - Full 4 Piece Kit MR2Heaven 1991-1998 Reproduction Mud Guards/Mud Flaps - Full 4 Piece Kit
MR2 Heaven MR2Heaven 1991-1998 Reproduction Mud Guards/Mud Flaps - Full 4 Piece Kit
from $139.99
$259.99

Notes 6/27/2022 12:20PM PST - 3 sets left. Next batch August-September 2022 6/23/2022 - Due to popular demand and nearly selling out 6 hours, we will increase the expedited count to a final 60 sets. Next batch will be in about 2 months from now 6/22/2022 - Soft launch sale price of $199.99. Extremely limited batch of 20-40 sets ready to ship in about 1 week. Next batch in August-September 2022. Purpose Highly desired and discontinued from Toyota so we came to the rescue Features OEM fitment - Faithful OEM reproduction 3D Scanned and CADed Direct plug and play - No modifications needed Constructed from high quality and durable/flexible rubber Integrated/Infused metal support plates at each mounting location for increased durability Fitment All 1991-1998 Toyota MR2 Notes Sold as a set of 2 or 4 pieces Replaces OEM Part #s 76621-17020 - Front Right 76622-17020 - Front Left 76625-19345 - Rear Right 76626-19355 - Rear Left 76095-17010 - Set of 4 76621-17020 76626-17040 76625-17040 Optional Rear Support pieces not included 76646-17010 76648-17010 Replacement fixation materials (most mr2s already have these installed) 90159-60298 - Black philips screw with washer 90189-06014 90159-60427 90119-06678 - M6x1.0 Socket head screw with washer

15

Have Questions?

Feel free to shoot us an email!

We Ship Worldwide!

Best Domestic and International Discounted Shipping Rates. We also help consolidate orders! Send us an email!

Satisfaction Guaranteed!

Don't like it? We'll make it right for you!

Most In Stock Orders Ship Within 1-48 Hours

We also offer multiple shipping speed options!