MR2Heaven Side Mount Intercooler Fan Shroud Kit MR2Heaven Side Mount Intercooler Fan Shroud Kit
MR2Heaven MR2Heaven Side Mount Intercooler Fan Shroud Kit
from $39.99

Purpose Our lightweight aluminum block off plate diverts and promote maximum air flow to an aftermarket side mounted intercooler. Without this plate, air would travel past your intercooler through the many holes and cracks causing rough turbulence and inefficient air flow when the vehicle is in motion. Our biggest 9" diameter lightweight aluminum fan shroud system provides high air flow to the intercooler and thus greatly improves intercooler system efficiency. By forcing and directing more air through the intercooler core, many users are noticing significant temperature drops. Advantages There has been at least 15+ different branded generic mr2 specific intercoolers on the market all with different specifications, sizes, different fitment issues throughout the past 25 years. While we have been able to procure in the past the most consistent quality, biggest, fattest, widest, best fitting core used out of all the manufactures, we still ran into into many quality control, consistency and supply chain issues with our 2018-2021 manufacuter. Our last intercooler core batch was ordered in May 2021 still has not arrived in 2022 after 8+ months and the fitment has become unusable as they started outsourcing parts and production to other manufactures due to pandemic/supply chain issues. We waited 8+ months for a batch of cores to the point where we were out of stock ourselves for months and after seeing that the newest batch samples were unusable, we are pretty fed up.  That is why in February 2022, we have decided to CAD everything and also to create/design our own intercooler core. An universal MR2 intercooler core with detailed specifications, utilizing the biggest core possible, with consistency and quality in mind and made using the best manufacturing/design and quality control methods available at our disposal through our vetted manufactures Our intercooler cores and various related parts such as fan shrouds/block off plates are CADed with detailed specifications, ensuring proper fitment, consistency and design. Our aluminum end tanks will be casted from a mold for repeatability and consistency. We will be using the widest and largest intercooler core on the market coming in at 200mm width x 235mm length x 100mm thick. We have also shortened the inlet and outlet diameter lengths of the end tanks by 10mm to account for a rare minority of 3SGTEs running into issues with the turbocharger being shifted very slightly from normal positions, resulting in the hot pipe being shifted away from the turbocharger outlet with no room for adjustment as the pipe touched the end tank's inlet inside the silicone hose coupler. Now there is significantly more room for adjustments. Better fitment and more adjustability/flexibility with intercooler pipes over other cores and more. That means our core will install cleaner and easier, and your pipes wont be forced to hit or rub against your Xbrace, look off when connected to your turbocharger or hot pipe rubbing cold pipe etc. Often times, to be real, the fitment issues will prevent pipes to be even installed for a small majority of 3SGTE owners (around 10%, as their turbo outlet position sits slightly off normal positions). For those owners to install, they need a very tall silicone coupler that allows enough flex/room for the hot pipe to connect. That small 10% will be eliminated with our 2022 cores as they provide more room for you to adjust Our intercooler core will be fitted in molds before all the components are welded to ensure consistency and quality control We've also adjusted tolerances of our red and yellow mounting brackets to stick out past the 100mm thick core by 1.5mm only. This ensures the intercooler core is in its intended place while in the car and does not cause fitment issues like the bullet points above. Some manufactures randomly bend aluminum tabs and randomly weld them and they're very off.  Our core mounting brackets were designed/reduced down to 2 repeatable dimension specific parts with simplicity in mind (As you can see the red and yellow brackets in our pictures).  Our cores will be shipped in a foam padded enclosure to ensure it does not get damaged during transit With our attention to details and strict QC on every part through our vetted manufactures, advantages in intercooler core design as well as in our perfectly fitting block off plate and 9" fan shroud, we are confident our exclusive kit is made to the highest of standards, is the highest quality, consistency and best performing side mount system on the market today, period. Features Largest 9" Fan and lightweight aluminum shroud system (The biggest you can mount on this core to help maximize cooling! It gets better.  As it is all about air flow, we offer 3 fans to choose from depending on your budget 9" Default China fan - 521 CFM (Tested) 9" SPAL Slim fan - 634 CFM (Tested) - 18% CFM Improvement.  9" SPAL Heavy Duty Fan - 808 CFM (Tested) - 48.5% CFM Improvement Our 9" shroud design is backwards compatible with SPAL branded fans for the highest flow if needed. We are also the only MR2 company to offer SPAL fans with our products as of Feb 8, 2022 (the date i am writing this). From our own testing, our 12V/31AMP SPAL 9" slim fan upgrade flows around 18.35% more air than the budget common 9" fan out on the market (which we also offer as default option). They're virtually almost identical but SPAL is higher quality in everyway, designed and built heavy duty (4oz heavier, coming in at 2lbs 4oz) and sports a much powerful motor. If that is not enough, we have an even bigger fan which flows 48.5% more air also. To properly utilize the full potential of your SPAL fan, we recommend using our dedicated wiring harness to properly power it. SPAL truly makes the best fans money can buy and we highly recommend it SPAL branded fans are used on NASCAR, modern supercars, as well as many other high end automotive racing organizations/manufactures. Their motors are fully sealed, dust proof and water proof. Individually balanced for long life and high performance. Our default 9" fan is not a slacker and is also commonly used. it features the same high efficiency straight blade 9" fan design for maximum air flow just like SPAL - Also from our testing, more RPM & air flow than the curved blades variant of the common budget fans out there during our testing 3D Scanned and everything is CADed for 100% best fitment with use of our intercooler cores.  CNC Cut & precisely bent according to specs Most consistent and Best Fitting on the market Slotted holes for slight adjustments if needed 5052 lightweight Aluminum Construction Maximizes intercooler efficiency and significantly lowers air temperatures for more horsepower/torque and less chance of knocking/pinging/detonation Hardware included Fitment Fits all 1991-1998 Toyota MR2 with upgraded side mount intercooler core This will 100% fit our cores. We cannot guarantee fitment on other cores made elsewhere) Fits all "Greddy" Style side mount intercoolers (ATS, KO, Berk, TCS, Ebay) that is commonly used on the MR2.  Notes This listing is for the 9" fan shroud, block off plate and fan. It does not include the intercooler core as pictured. If you need the core, please visit our other product pages.  Pair this with our dual fan shroud for maximum performance Does not work on the OEM intercooler. Must have upgraded intercooler. Click here For full intercooler kit, click here

-4% sale
Stainless Steel Intercooler Pipes - For Side Mount Intercooler SW20 3SGTE MR2 Stainless Steel Intercooler Pipes - For Side Mount Intercooler SW20 3SGTE MR2
MR2Heaven Stainless Steel Intercooler Pipes - For Side Mount Intercooler SW20 3SGTE MR2
$289.99
$299.99

The best pipes on the market. Interchangeable with all types of common blow off valves, simply twist on the flange, including OEM. Mirror polish, our piping kit is sure to turn heads.  FEATURES & ADVANTAGES Stainless Steel Construction Polished Surface for lower radiant heat absorptivity rate Rolled Bead for efficient hose coupler attachment Smooth pipe transitions for strong seal and hose connections  Universal Interchangeable twist on BOV Flange System - Exclusive to MR2Heaven Pipes. (Easily twist on different flanges - OEM, HKS, Greddy, TIAL Blow off valve Flanges and our Blow off valve delete cap) Pipe also available with no BOV port Includes A set of Stainless Steel Cold and Hot Pipe Optional MR2Heaven Fully interchangeable Stainless Steel BOV Flanges (Easily Change between OEM, HKS, Greddy and TiAL, and our BOV delete cap blow off valve flanges) - This system is unique to MR2Heaven pipes only Optional Premium BREEZE Constant Torque Hose Clamps (not your common cheap T-Bolt clamps) Optional Set of MR2Heaven multi layered and reinforced silicone hose couplers Fitment Fits all GEN2/3/4/5 3SGTE on aftermarket side mount intercooler and bottom mount turbo (example, CT26, CT20B, most bottom mount turbo kits) Replica Greddy intercooler cores (Authentic Greddy Cores have longer inlets and modifications would be needed) If you are looking for a full intercooler kit, click here Plug and Play Setup. No modifications needed! Notes This kit works extremely well with our dual fan shroud kit, significantly lowering air intake temperatures while possibly matching the SS theme with our mirror finished shroud. Click here Complete the SS Pipe collection with one of our 3 or 4" Intakes here OEM BOV flange works with OE GEN2/3 BOV, not OE GEN4 (That means you can throw a gen2/3 bov on a gen4 and it'll work, just cant throw a OE Gen4 BOV on the flange) NEW OEM Twist on Blow off valve flange. HKS, Greddy, Tial also available.  Want even more performance? Check out our Carbon Fiber Pipes here     

0% sale
Carbon Fiber/Forged CF Intercooler Pipes - For Side Mount Intercooler - (NEW VERSION 2, 2020+) Carbon Fiber/Forged CF Intercooler Pipes - For Side Mount Intercooler - (NEW VERSION 2, 2020+)
MR2Heaven Carbon Fiber/Forged CF Intercooler Pipes - For Side Mount Intercooler - (NEW VERSION 2, 2020+)
$449.99
$449.99

Note 11/23/2020 - Introduction of our Forged Carbon Fiber Intercooler pipes NOTE 3/1/2020 NEW Version 2 Carbon Fiber Pipes (Applies to all new orders fulfilled after 3/1/2020). We've invested, upgraded and improved on our manufacturing processes and design for creating these carbon fiber pipes. The result? Significant improvements and the result is a high quality and premium carbon fiber piece. A totally different level and quality pipe dubbed Version 2. See details below. PURPOSE Ever wondered why most turbocharged cars would pull hardest on the first pull of the drive and quickly fall flat on its face afterwards after the 3rd pull? With more heat in the intercooler system, the less power an engine can crank out as it has to keep itself from knocking and detonating. With our Carbon Fiber Intercooler pipes and feedback from our users, we are currently seeing an average of 20-30F maximum increase over ambient as well as faster temperature recovery times, on the race track or on the streets with or without traffic! A Game Changer Intake Air Temperatures with Stainless steel/Aluminum pipes can exceed 130-165F after 3 to 6 pulls on an upgraded side mounted intercooler setup. 165F is ridiculous considering modern high performance cars are only about 10-30F above ambient. Fortunately for this application, our real world testing has shown that these pipes reach up to 30 degrees above ambient on the track or on the street. This is made possible because Carbon Fiber features 10 to 40x lower heat thermal transfer conductivity values than Aluminum and Stainless steel material respectively. This means, it’s an excellent insulator, like styrofoam and silicone. (Touch styrofoam and silicone, they have a hard time reaching any sort of significant temperatures)   Exhaust manifold temperatures can reach up to 1200F with your valve cover temperature itself hovering around 185-260F+. According to thermodynamic principles, a metal piece will become equilibrium in temperature with its surroundings very quickly. The metal piece would also absorb outside radiated heat and also radiate it within the pipe since air charge temps are cooler inside the pipe than the metal heat soaked piece. Ever wondered why Koenigsegg uses Carbon Fiber intake manifolds and intercooler pipes on their most exotic and highest performing cars?  Ever wondered why engineering marvel and high performing Buggatti Chiron, a car that Shattered land speed record with 305 Miles Per Hour, a 3 Million Dollar+ Supercar chooses to use carbon fiber for their intercooler pipes and intake manifolds?  Considering their vast budget available and being owned by Volkswagon (One of the biggest car groups around), out of all the materials available at their disposal and under a strict "motor/car cannot fail during extreme fully continuous use" mindset, they chose to design their pipes out of Carbon Fiber. Not Plastic, Not Rubber, Not silicone, but Carbon Fiber. FEATURES AND ADVANTAGES Carbon Fiber Intercooler Pipe Advantages  Lowers Intake Temperatures - Excellent insulator – Great resistance to heat entering the piping/intercooler system (See reasons above) Higher intercooler efficiency Faster temperature recovery times Pipes stay warm to the touch - Prevents pipes from becoming hot thus causing "heatsoak" and warming up air inside the pipes. More horsepower and FUN throughout your whole drive. Lightweight The GEN2/3/5 Pipes (Both cold and hot pipes w/o BOV flange combined) weigh as much as a medium sized water bottle at 1.1 pounds! Stainless Steel pipes would weigh 7lbs+. Rolled bead design on pipe connection ends helps prevent popped couplers Reinforced End Sections - For Version 2 (2020+) To further improve on our pipes, the ends of the pipes have extra carbon layers for improved structural rigidity.  Reinforced Optional Universal Blow Off Valve Port system (New for Version 2, 2020+) – Billet CNCed Aluminum BOV port with an additional milled protruding lip encapsulated by new high strength epoxy ensures structural strength, durability and rigidity. Exotic, modern and great to look at(Pair it up with some of our other CF engine bay offerings!) Blow off valve support No BOV  Stock BOV (Twist on version NEW for V2 2020+) – Interchangable with all our other BOV options. Can also revert back to no BOV with our BOV block off plate) Greddy, HKS or Tial BOV Port (Interchangeable with our universal aftermarket BOV port) Smooth Insides (NEW FOR V2 2020) – Gone are the days of high and low spots as seen on our v1 pipes. For our new updated Version 2 2020+ pipes, we’ve made strides in upgrading our manufacturing processes. By investing in many new molds to create rubber inflatable cores to use during pipe production, we were able to eliminate the use of generic bagging material which does not produce smooth surfaces when twisted, leaving high and low spots throughout the insides of the pipe. By utilizing new rubber inflatable cores that are pre-shaped exactly as our pipes instead of using generic bagging material ensures inside surfaces are smooth during curing and that the pipe has consistent pressure throughout every inch of the curing process. This new upgrade in manufacturing processes/technology ultimately increases pipe overall structural strength, rigidity, durability significantly and insides of these pipes are now super smooth.  Made from 8+ layers of high quality and temperature PrePreg Carbon Fiber Dyno tested400WHP on a GTX3076 at 19PSI as well as a CT15B at 19PSI @ 360WHP Track testedCT15B @ 18PSI at 350WHP, 22-30 degrees above ambient intake air temperatures INCLUDES 1x CF Hot Pipe 1x CF Cold Pipe Optional Constant Torque hose clamps and a set of MR2Heaven couplers (+$50) Notes Supports GEN2, GEN3, GEN4 and GEN5 3SGTE. Does not fit the Authentic greddy intercooler core as they are different dimension (See our intercooler product page if you need a intercooler core) OEM BOV flange works with OE GEN2/3 BOV, not OE GEN4 (That means you can throw a gen2/3 bov on a gen4 and it'll work, just cant throw a OE Gen4 BOV on the flange) Important: Due to the manufacturing process we recommend thoroughly inspecting/cleaning the inside of the pipes prior to installation.   NEW OEM Twist on Blow off valve flange. HKS, Greddy, Tial also available.   Stock GEN4 3SGTE - 360WHP, 343ftlb Torque @ 19PSI with OEM CT15 Billet Turbo Upgrade and MR2Heaven Carbon Fiber Pipe Intercooler Kit  

-51% sale
MR2Heaven GEN 2/3/4/5 3SGTE MR2Heaven GEN 2/3/4/5 3SGTE
MR2Heaven MR2Heaven GEN 2/3/4/5 3SGTE "ONE PIECE" ALUMINUM INTERCOOLER PIPES
from $99.99
$199.99

Purpose These are LIGHTWEIGHT ALUMINUM One Piece intercooler pipes for your 91-98 Toyota MR2 with a 3SGTE engine! We support generation 2, 3, 4 and 5 3SGTE motors. We're confident that we offer the best flowing pipes available on the market.  Features Designed as REAL 1-PIECE piping, not a bunch of pipes welded together as others on the market. These pipes allow for a cleaner look Weight advantage - Our Gen4 3SGTE varient pipes weighs 3.3lbs vs 7.5lbs stainless steel pipes offered by our competitors) Smoother flow transitions with more ideal angles and bends thus increasing intake velocity within the pipes, thus more FLOW, less restrictions and MORE HORSEPOWER! Wont pop off hose couplers as easily as other pipes on the market as our pipes allow for more surface area to be clamped down by hoses. Gone are the days of pulling over on the road or going home to fix pipe connections that have blown off due to a bad design/fitment. Does not rust(perfect for water/ethanol injection) Included MR2Heaven Custom polished aluminum Intercooler Hot Pipe MR2Heaven Custom polished aluminum Intercooler Cold pipe  (4) Silicone couplers & (8) Heavy duty T-bolt clamps (Optional) Notes This standard setup comes without a BOV flange(No Blow off valves). (Cleaner look, less chance of leaks, faster spool, toyota proven effectiveness and more response running without an BOV flange)

-61% sale
Engine Lid Dual Fan Shroud (Forged Carbon Fiber/Mirror Finish/Carbon Fiber/Raw Aluminum) Engine Lid Dual Fan Shroud (Forged Carbon Fiber/Mirror Finish/Carbon Fiber/Raw Aluminum)
MR2Heaven Engine Lid Dual Fan Shroud (Forged Carbon Fiber/Mirror Finish/Carbon Fiber/Raw Aluminum)
from $169.99
$429.99

How It works - Lower temperatures. More horsepower. More Fun.  This dual fan shroud setup helps lower temperatures and promotes horsepower in many ways. -By introducing large amounts of cold ambient temperature air into the whole top portion of the engine bay, this helps your pre-turbo intake system (especially aftermarket intake systems with the filter simply hanging around in the engine bay) draw in much cooler air into the turbocharger right from the get go. This means your intercooler system has a much easier time, is less heatsoaked overall, and temperatures in the whole system are much cooler right from the start.  -Large proportion of air introduced from under the car at speed, side vents/side mount intercooler fan as well as heat radiating upwards from the 900-1400F exhaust manifold/190-220F motor ends up re-circulating/hanging out under the restrictive stock engine lid and has no where to go. This heat, at best is pretty warm also essentially ends up being sucked right back inside your intake system. As we all know, heat rises right? Yes, straight from your burning 250 degree valve cover into your intercooler pipes that is. Simple question. Ask yourself why your intercooler pipes and intake manifold are burning hot after driving with all this "natural air flow" going on? Shouldn't it be cool to the touch? Not quite.  -With "hot" and "cold" intercooler pipes and the intake manifold itself being made of metal and most of the plumbing (quite a bit of length and air volume there too) literally sitting 1-4 inches above the consistent 185-250 degree valve cover/400-1400 degree exhaust manifold at all times, this naturally introduces significant heat soak and unnecessary heat increases via heat radiation, especially at part throttle or idling when air is moving rather slow within the system. (Try it for yourself - Go put your hand 1-4 inches from your hot heat soaked brake rotors after a spirted drive, wave your hand around close to it and see if the air gets any cooler? You'll see it doesn't. Scared of getting burned? Thats essentially the same kind of unnecessary heat your baked, hot intercooler pipes radiates off when air is moving through inside regardless of speed. That kind of warm/hot air temperatures will definitely rob horsepower.  -These two 12" fans will literally have both your intercooler pipes as well as complete top half of your intake manifold much cooler and cold to the touch (Instead of being too hot to touch safely) during your whole drive. We guarantee it. Touch it. Try it yourself. If you have a top mounted a2a ic, this will make it much cooler also. By having cold pipes you can touch, this helps your intercooler core "literally chill around" as it does not have to battle unnecessary heat in the system, helping it stay cooler all the time and ready to go at a moments notice. By also having a cold pipe and top half of the intake manifold that is actually cold to the touch, the warmer air inside will get chilled as well. Thats right, your intercooler will be chillin (see here), and warmer air coming out the intercooler after it does its cooling, while inside the cool pipes/intake manifold will be cooled a bit more before making its final entry into your cylinders instead of being warmed back up otherwise without our dual fan shroud. Talk about an easy smooth chill journey. Cooler temperatures = more power, less knock, pining and more fun. We all know that. Heat soaking is a thing of the past. Say thank you to fast recovery time!  With all that being said, many customers are seeing a 30-40 degree difference in their intake air temperatures inside the intake manifold with our fan shrouds installed on their drives. We all know how hard our cars pull on a 45 degree night vs a 95 degree day on the first pull, before it falls flat on its face after the 3rd pull without our fan shroud. The huge horsepower difference is undeniable, that is because we are losing 20-70+ horsepower due to temperatures alone and the ECU having to resort to safer timing values/maps for your car to run safely. The end result with these installed is MORE HP and MORE FUN throughout your whole drive. Guaranteed. Pro tip - Pair the dual fan shroud with our 9" extreme 800+ CFM spal intercooler core fan (see here) for the ultimate experience. If you are using a cheap 9" or even worse a 200-300 CFM 7", please strongly consider. Note - Please buy 2 dedicated wiring kits if you are upgrading to SPAL IC fan + dual fan shroud setup Features: Lower Air Temperatures and increases horsepower - Contrary to popular belief the mr2 engine bay and its "natural air from under the car and through the engine lid vents" is not efficient in cooling necessary components at all, if anything, it heat soaks components. With both fans on, BLOWING INTO the engine bay, we and other customers noticed side mounted intercooler core/air intake charge temperatures dropping 20-40 degrees F. Additionally, intake manifold, IC pipes, intake, and top mounted intercoolers temperatures, side mounted intercooler temperatures all dropped significantly. Pulling air upwards, DOES NOT WORK. You're forcing radiated heat soaked air from under your hot valve cover/other engine components into your pipes. The air will have to travel past multiple hot objects first, absorb nearby heat, then pass the pipes before reaching the fans. By brute forcing huge amounts of CLEAN ambient temperature air into the engine bay at such close proximity interrupts the process of heat rising into the pipes from hot exhaust manifold/valve cover and will actually cool the pipes and everything near by down significantly better, not the other way around. Available in Full Carbon Fiber, Mirror Finish or in raw aluminum form Lightweight (CF version around 1/3 the weight of aluminum panels and 1/6 weight of steel) Modern Exotic appearance Premium, stylish & sleek Cut with water, no burn or poop marks from laser cutting Brushed aluminum finish Show off and compliment that precious engine bay/hard work in a classy way Premium CNC cut full sized panel - Not half sized panel or hand cut Dual 12" fans (Same bolt pattern as many of the common engine lid fans out there) Send us an message for specifics. Tested and verified - A whopping peak 3300-3400 CFM of air flow. Thats about 6-7x the airflow of the common 9" intercooler fan we sell when strapped onto an IC core (That fan isn't a slouch either), or 4.25x our thick fat extreme 9" HD Spal. Yeah.  Carbon Fiber version will look great with some of our other Carbon Fiber offerings (CF intakes, CF Intercooler pipes, CF pre preg interior trims, CF T-Top shades, CF 98 Wing riser plates, CF stage 2 wing, and even more in the future. Stay tuned for the releases! Notes Sold as a single panel or as a full kit with fans and hardware. Wiring is not included as these fans can be wired up easily in many different ways. Raw Aluminum material in itself is a very prone to permanent finger printing/marring and easy to scratch material. It is also subjectable to water marks that may be difficult to remove once etched on.  Pro-Tip - Paint aluminum surface with $5 high temperature black spray paint or any paint of your choice for a nice finish :). See picture.   

-14% sale
MR2Heaven OEM Plus Seat Covers (Black, TAN, Black W/ Red Stitching, Black/Red Hybrid, BLUE, Black Alcantara/Leather with Black Stitching, Black Alcantara/Leather with Red Stitching) MR2Heaven OEM Plus Seat Covers (Black, TAN, Black W/ Red Stitching, Black/Red Hybrid, BLUE, Black Alcantara/Leather with Black Stitching, Black Alcantara/Leather with Red Stitching)
MR2 Heaven MR2Heaven OEM Plus Seat Covers (Black, TAN, Black W/ Red Stitching, Black/Red Hybrid, BLUE, Black Alcantara/Leather with Black Stitching, Black Alcantara/Leather with Red Stitching)
from $389.99
$449.00

Purpose   Tired of torn, ripped and worn out 24-30 year old seat covers? Give your interior a complete transformation and bring your car back to life with these covers!    Features Proven and used by our team to restore high end MR2s, often selling for $15-30k+. High quality and durable soft pvc leather Comes padded High Strength Nylon Stitching Storage Pouch behind the seats like OEM Plug and Play (Replicates OEM mounting tabs so no modifications necessary) Easy to Install (Cut up your old covers, wrap these on, attach and secure into place using OEM hardware and retaining rods) Heated Seats Option - Great for winter Available in optional Alcantara - These are super grippy, great for spirited driving! Available color/choices All Black **POPULAR All Black with Red Stitching **POPULAR All Tan All Blue Black/Red Hybrid with Red Stitching - About 15 sets of these are currently in stock and once they're gone, they're GONE (No current plans on stocking those, phasing out) All Black JDM Style Leather/Alcantara **POPULAR All Black JDM Style Leather/Alcantara with Red Stitching **POPULAR Matching door card inserts here   Notes *One order is enough for both seats* - Includes 2 seat cover kits, enough to do both seats. These do not wrap over your existing covers. These are a full replacement of your existing covers. Fits all 91-98 Toyota MR2 OEM Seats (no pre made holes on sides so can be used for NA seats as well as RHD and LHD, for those with bolster and lumbar adjustments holes will need to be made) These are side specific, check your seat bottom lumbar support to tell them apart. (One side of the bolstering is thicker and bigger than the other side) Pro Tip #1 - Keeping all your leather parts conditioned periodically will significantly prolong its lifespan and durability. Sunlight and drying out is the main enemy for all leather.  Pro Tip #2 - A steamer on a low setting (not a heat gun) will significantly remove any wrinkles and create a tight fitting contoured look!

-54% sale
MR2Heaven Door Panel Leather MR2Heaven Door Panel Leather
MR2Heaven MR2Heaven Door Panel Leather "Door Card" Inserts
from $129.99
$279.99

Features Available in Black, Red, Tan, and blue leather with optional red stitching on black colored variants Alcantara variants also available - All Black Alcantara with optional red stitching Made from the same leather/Alcantara material as our current seat covers OEM Perforated Leather Variant Style available 4 Striped Variant Style also available Flexible stainless steel backing with Bend-able Clip design just like OEM - Holds sturdily in place. If you are on OEM cloth door panels, will need to drill into your door panel for clips to slide through and bend into place, an easy 10 minute procedure.  Comes fully assembled with foam and glued Also available as a DIY backing kit (For Do it yourself with your own design) Fitment All 1991-1998 Toyota MR2s Direct plug and play for OEM door panels with holes already pre-drilled Will require minor additional work for cloth door cards such as removing the original cloth with an exacto knife, drilling holes on cloth door panels for the bendable retaining clips, and may require some foam to be trimmed/removed near the door handle area for proper fitment.  Notes Sold as a set for both doors (only order 1 per car) Matching seat covers here Installation instructions here  

-9% sale
MR2Heaven 3 Point Front Strut Tower Brace W/ Optional Brake Master Reinforcement MR2Heaven 3 Point Front Strut Tower Brace W/ Optional Brake Master Reinforcement
MR2 Heaven MR2Heaven 3 Point Front Strut Tower Brace W/ Optional Brake Master Reinforcement
from $254.99
$279.99

Note 4-21-2021 - Phasing out white and silver color Purpose Introducing our NEW Front Tower Braces with optional Brake Master Cylinder Support add on to increase brake pedal feel. 😍 These strut tower braces help decrease chassis flex and promote proper suspension geometry under load.  A 10mph increase in speed during a sweeper is easily achievable while feeling the same amount of body roll with a good strut brace on the MR2. Features 3D Scanned, CAD designed and verified for fitment CNC Mold Jigs were made to produce these braces Aluminum construction for high strength and light weight (~4.99lbs with BMC brace) Greatly Increases chassis rigidity  Promotes proper suspension alignment/geometries under load Increases cornering speeds and driver confidence Custom High Strength Aluminum Bar Profile Design Exclusive to MR2heaven only (You wont find another bar in this shape anywhere else) Comes powder coated in matte black High quality welds Billet Aluminum CNC Flanges/Mounting cage for cleaner look and increased structural strength.  Optional Billet One piece Aluminum CNC Integrated Brake Master Cylinder Brace Support available for increased brake pedal feel Notes  Brake master add on does not work with ABS Equipped MR2s, only for non ABS

-14% sale
MR2Heaven Rear X Strut Tower Brace MR2Heaven Rear X Strut Tower Brace
MR2 Heaven MR2Heaven Rear X Strut Tower Brace
$189.99
$219.99

Gone are the days of finding a rare TRD X Brace. This brace is a faithful reproduction of the highly sought after Strut tower brace from TRD. As many already know, the MR2 chassis is quite soft and flexible. When your chassis flexes, your alignment is off, thus affecting performance and producing a less than confidence inspiring ride. Purpose Reduce chassis flex so your alignment can work more efficiently/effectively.  Many customers report that they can "Easily drive another 10mph+" through identical sweepers with the same amount of body roll with this installed. Reduce body roll and restores confidence inspiring feel Features Constructed from High Quality Stainless Steel 304 Easy to clean and keep clean Plug and Play, no modifications needed Fitment Fits all 91-98 Toyota MR2s Notes Does not work with GEN5 3SGTE due to OEM oil cap Install with car resting on its wheels/suspension in its natural driving state, not on jacks or lift.

-4% sale
Reproduction JDM Front Solid Side Moldings (Front Side Marker Deletes) Reproduction JDM Front Solid Side Moldings (Front Side Marker Deletes)
MR2 Heaven Reproduction JDM Front Solid Side Moldings (Front Side Marker Deletes)
$124.99
$129.99

 Reproduction (discontinued from Toyota) FRONT Solid Fender Moldings Are Finally In Stock and they look GREAT!!! OEM Style Reproduction Plug and Play, no modifications needed Cleaner and more modern look Embedded Metal Plate within Rubber strip (Similar to OE design) for Excellent Structural Support, can be molded/contoured for easy fitment. Stainless Steel Hardware for protection against corrosion  Comes in standard flat black color Included 1 Pair/Set of Moldings (Left and Right) Zinc Plated M6x1.0 Mounting Nuts Fitment All 1990-1998 Toyota MR2 SW20 Front: between fenders and front bumper, deletes 2 piece front side markers Notes: Test fit these before painting. Once painted, we do not accept returns. These are flexible to your liking. Make the necessary modifications if necessary, set the necessary flex if needed to match your bumper before painting. Toyota had more than 6 variations of these moldings for different markets/years. So this will fit a majority of cars but not all, so please verify before painting.  We advise painting to match your cars color and to increase the longevity of these moldings. These are made of rubber and will eventually dry up and develop cracks if not covered/protected from UV rays. These can develop cracks in as little as 1 month to 1 year if left unprotected/unpainted, depending on severity of the UV rays. As of today (5/2/2021), if painted, these have lasted 2.7+ years without cracking since product launch/painting/install from July 2018.

-9% sale
MR2Heaven Reproduction Steering Column Covers (Carbon Fiber Available) MR2Heaven Reproduction Steering Column Covers (Carbon Fiber Available)
MR2Heaven MR2Heaven Reproduction Steering Column Covers (Carbon Fiber Available)
from $109.99
$119.99

  Purpose Reproduction Steering Column Covers "Clamshell or Clam Shell Covers as often referred to" from MR2 Heaven. These covers have been discontinued by Toyota for quite some time. Fortunately, we are here to bring them back! We've heard you loud and clear! About 75%+ of the cars we encounter all have broken covers behind the steering wheel so its time for a change. These covers are commonly broken at the mounting tabs on the side as well as at the mounting holes underneath the cover. Age of the plastic, improper removal, fatigue, over tightening the screws, brittleness as well as impact are common reasons why these covers fail.    Features Available in overlaid Glossy Carbon Fiber and regular ABS Plastic.  Beefed up mounting tabs Direct plug and play Hardware kit included   Notes Designed for LHD USDM MR2s. (If your car is not a US mode please compare yours to our photos to verify the holes on the bottom match up in the same locations) Future batches may include RHD and various variants.   

Front Hood Gas Strut Kit Front Hood Gas Strut Kit
MR2Heaven Front Hood Gas Strut Kit
from $89.99

Our new V2 utilizes our exclusive and proprietary custom made rod ends and thinner diameter strut tubes resulting in perfect fitment and interference free operation. Now also available in full Stainless Steel for even more bling If you are using v1 and would like to upgrade to V2, let us know! Purpose Its that time to discard that rusty, squeaky, clunky, outdated 30+ year old dangling loose rubber grommet and probably bent hood rod. Oh yeah, forgot to mention, its cumbersome and a pain in the butt to rotate around and stick into place. If strong wind topples your hood, good luck down there. That hood is metal, around ~56 lbs and has a sharp metal protruding hinge.  We spared our customers time, frustration and confusion, spent our own time, effort and money, did the research and tested extensively to package the most efficient and best fitting front hood prop system for you. We found nothing on the market worked without interference (often times hood would deform, bow up near the middle of fender and destroy your paint on hood/fender in the process -Hello rust), so we made our own parts and now present to you our headache free, perfect fitment and interference free hood strut kit. Pretty much every premium or high end new car has gas struts installed for luxury and convenience. Why not you?  Now you can... Have your hood opened with minimal effort Have your hood opened half way just cause... Eliminate that fear of wind or a person toppling your hood on top of you while working on the car.  Stand out of the crowd with new high quality MR2Heaven Front Hood Gas Prop Kit Modernize your ride! Have a sick looking car while the hood is open, like ours for example.. :) Included High quality pair of Guden Struts (Struts made in USA/Korea/Turkey depending on batch and material selected) Hardware kit Everything else needed to modernize your whip! Fitment All 1991-1998 Toyota MR2s with OEM hood/fender. Aftermarket hood/fender support has not been tested Notes We also have a rear engine lid gas shock kit as well here PLEASE FOLLOW INSTALLATION INSTRUCTIONS.   

-13% sale
Engine Lid Gas Strut Kit Engine Lid Gas Strut Kit
MR2Heaven Engine Lid Gas Strut Kit
$69.99
$79.99

Features Billet 6061 Aluminum CNC'ed brackets for nice looks and quality.  Brackets are polished for a great shine. Looks great as is or with other chromed, stainless  steel or polished parts.  Versatile - Engine prop works on both sides of the engine bay and in other challenging environments. Simply rotate the bracket or mount it to a different location on engine lid to clear difficult strut braces or other clearance issues Shock strength strategically chosen to prevent overpowering and bending of the engine lid when compressed.  Included 1 High Quality SUSPA Gas shock 2 Aluminum CNC'ed brackets Hardware kit   Notes We also offer a hood strut kit here - Very Useful This strut kit works for both Turbo and NA engine lids    

-11% sale
Carbon Fiber *Snap On* Cover for GEN4 3SGTE Valve Cover Carbon Fiber *Snap On* Cover for GEN4 3SGTE Valve Cover
MR2Heaven Carbon Fiber *Snap On* Cover for GEN4 3SGTE Valve Cover
$249.99
$279.99

Note 4/23/2022 - Back in StocK! Purpose   Our new MR2Heaven Carbon Fiber Snap On Cover for the GEN4 3SGTE OEM valve cover. Just snap it in!   Add some bling to that engine bay!   Vibration resistant and helps prevent rain from seeping into the spark plugs which commonly causes ignition problems for folks using engine lid fan shrouds.    Features Snaps into place using high temp resistant rubber clips and ball studs, similar to what OEM manufacturers use (Included in our hardware kit) Vibration resistant design Cleans up the appearance of engine bay Cleaner, stylish, modern and exotic appearance Resists rain from getting directly into the spark plugs valleys Includes 1 MR2Heaven Carbon Fiber Cover Hardware kit Instructions   Note   GEN4 OEM Valve cover itself is not included..

-15% sale
SW20 Gauge Cluster Aluminum Bezel Rings SW20 Gauge Cluster Aluminum Bezel Rings - MR2 Heaven
MR2 Heaven SW20 Gauge Cluster Aluminum Bezel Rings
$59.99
$69.99

Modernize that interior with these snap on rings! 

164

Have Questions?

Feel free to shoot us an email!

We Ship Worldwide!

Best Domestic and International Discounted Shipping Rates. We also help consolidate orders! Send us an email!

Satisfaction Guaranteed!

Don't like it? We'll make it right for you!

Most In Stock Orders Ship Within 1-48 Hours

We also offer multiple shipping speed options!